how to build a wooden lamp post

Welcome to the web site Best Blog Hồng, At present best.bloghong.com will introduce you to the article how to build a wooden lamp post
, Let’s be taught extra about it with us. methods to construct a picket lamp publish
article under

In case you’re on the lookout for a classy and unique technique to spruce up your own home’s landscaping, effectively, look to the proper.

This outside lighting mission is deceptively easy to construct. Made from rot-resistant western crimson cedar, the fixture consists of a 2×4 heart publish to anchor it, a horizontal arm to carry the lantern, and 1×6 cladding that yokes the 2x4s collectively and creates engaging shadow strains. Fitted with a good-looking copper-and-glass candle lantern, it exudes Zen-like magnificence day and evening.

Studying: methods to construct a picket lamp publish

This Previous Home senior technical editor Mark Powers put in our lamppost alongside a backyard path however says its proportions would complement just about any outside area, from a patio to a water function. In case you’d favor to wire the lamppost for low-voltage lighting, he reveals how to do this, too.

SHOWN: H. Potter Craftsman Lantern, 9¾ by 10½ inches, $80; H.Potter

Watco Teak Oil End, $11 per quart; Rust-Oleum

Obtain and print the lamppost reduce record

Step 1: Lamppost Overview

Illustration by Gregory Nemec

Day-to-day timeline

  • Day 1: Lower to measurement and form the cedar boards (Steps 2-8).
  • Day 2: Assemble the lamppost and set up it (Steps 9-18).

Pathway Lamppost Lower Record

  • 2×4 posts: 1 @ 6 ft
  • 2×4 crossarm: 1 @ 12½ inches
  • 2×4 crossarm: 1 @ 3 inches
  • 1×6 publish cladding: 2 @ 4¾ inches with a 45-degree beveled high
  • 1×6 publish cladding: 2 @ 36 inches
  • 1×6 crossarm cladding: 2 @ 27 inches with 1-inch noses and 45-degree angled ends
  • 2×10 base trim: 2 @ 6 inches
  • 2×10 base trim: 2 @ 7½ inches

Each items with a 45-degree beveled edge on the high and measured between lengthy factors of the mitered ends

Obtain and print the reduce record

Purchasing Record

  • 2×4 frequent cedar board. Get one 8-footer to make the middle publish and lantern arm.
  • 1×6 clear cedar boards. Get two 8-foot lengths to clad the publish.
  • 2×10 clear cedar board. Get one 6-footer to wrap the bottom of the publish.
  • development adhesive
  • 2- and 2½-inch-long ending nails for a pneumatic nailer
  • ⅜-inch hardwood dowel
  • -inch-diameter spade bit waterproof carpenter’s glue to attach dowel rods in place
  • polyurethane glue for mitered joints on the ornamental base
  • 100-grit disks for the random-orbit sander
  • 1-inch screw hook for hanging the lantern or gentle fixture
  • copper candle lantern
  • low-voltage land-scape gentle fixture (non-obligatory)
  • transformer (non-obligatory)
  • 12-volt cable (non-obligatory)
  • cable staples (non-obligatory)

Step 2: Crosscut the two×4 to Size

Photograph by Kolin Smith

Check with the reduce record. Use a sliding compound miter noticed to crosscut the two×4 into three lengths: the lengthy vertical heart publish and the 2 shorter items that make up the core of the lantern arm.

Step 3: Miter the Publish Finish

Photograph by Kolin Smith

Set the miter-saw blade to its sharpest angle (some go to 55 levels) and trim the underside finish of the middle publish. The ensuing sharp level will permit you to later pound the publish into the bottom with a sledgehammer.

Step 4: Lower the Wiring Channel

Photograph by Kolin Smith

Comply with this three-step sequence should you plan to attach a low-voltage panorama gentle fixture. If not, skip to Step 7.

Mark the centerline of the publish from the place it can meet the bottom to its intersection with the lantern arm, 6¼ inches from the highest of the publish.

Use a ½-inch spade bit and a drill/driver to bore a ½-inch-deep gap at that intersection. To make the wiring channel, set the blade of a round noticed to ½ inch deep and make a number of cuts parallel to the centerline, not more than ¼ inch to both aspect.

Do the identical from the drill gap in the direction of one fringe of the board.

On the lantern arm, observe the identical course of to proceed the channel from the publish; drill an analogous flip gap 2 inches from the tip, and reduce a channel to the sting to achieve the lantern.

Step 5: Take away the Waste Wooden

01 lamppost Photograph by Kolin Smith

Use a wooden chisel to pry out the waste wooden from the channel and scrape it clear.

Step 6: Set the Cable within the Groove

01 lamppost Photograph by Kolin Smith

Learn extra: methods to get your canine to cease lunging at vehicles

Lay the low-voltage electrical cable within the groove, ensuring to depart just a few ft further on the lantern arm.

Fasten the cable in place with cable staples. Be aware that 12-gauge low-voltage cable is adequate for many panorama lighting methods that complete 200 watts or much less.

Tip: Alter your mixture sq. to the gap between the sting of the publish and the sting of the channel, and use that setting to keep away from puncturing the cable in Steps 9 and 18.

Step 7: Mark the 1×6 Arms

01 lamppost Photograph by Kolin Smith

Lower to size the 2 1×6 boards to clad the lantern arm. Use a mix sq. to mark a 45-degree cutline on every finish of each crossarms.

Place the strains in order that 1 inch of the boards’ ends stays sq..

Step 8: Lower the Items

01 lamppost Photograph by Kolin Smith

Set the miter noticed to 45 levels and trim the arms on the cutlines you marked.

Subsequent, you may reduce the 4 1×6 boards to clad the middle publish.

First, although, bevel one finish of every board at 45 levels and use these ends to make the brief items that match straight above the lantern arm.

Step 9: Lay out the Cladding

02 lampposts Photograph by Kolin Smith

On a flat work floor, prepare the three 1×6 items that make up one aspect of the lamppost, as proven.

Step 10: Place the two×4 Components

02 lampposts Photograph by Kolin Smith

Lay the two×4 heart publish on the boards. To heart it, use a 1-inch-wide scrap-wood block and shift the two×4 till the block is flush with one fringe of the 1×6.

Mark the two×4’s ultimate place with a pencil, and repeat the method for the lantern arm.

Step 11: Be part of the Publish Components

02 lampposts Photograph by Kolin Smith

Take away the middle publish and arms, apply development adhesive to them, and press them into the outlines on the cladding.

Tack the two×4 items with a pneumatic ending nailer and 2-inch-long nails. In case you put in {the electrical} cable in Step 4, you’ll want to preserve the fasteners inside 1½ inches of both fringe of the two×4. Apply development adhesive to the uncovered faces of the 2x4s and set the remaining cladding in place; use your mixture sq. to align it with the other layer of cladding.

Press the boards down. For added energy, you possibly can tack this cladding in place with a pneumatic ending nailer and 2-inch-long nails. In case you do, you’ll want to fill and sand the nail holes.

Step 12: Bore the Dowel Holes

02 lampposts Photograph by Kolin Smith

To strengthen the joint between the publish and the lantern arm—and to lend the piece a handcrafted look—set up two hardwood dowels.

Use a mix sq. to attract a 45-degree line the place the publish intersects the arm. Make two marks alongside the road, 2½ inches in from every nook.

Learn extra: How to attract a lion face simple step-by-step

Slip a scrap board beneath the joint, then use a drill and ⅜-inch-diameter spade bit to bore two holes on the marks; go fully by way of to the opposite aspect.

Step 13: Trim the Dowels

03 lampposts Photograph by Kolin Smith

Smear waterproof carpenter’s glue or polyurethane glue onto a ⅜-inch hardwood dowel.

Faucet the dowel into one of many holes till it protrudes no less than ⅜ inch from the other aspect. Trim off the surplus dowel with a Japanese-style flush-cutting handsaw, as proven.

Peg the remaining gap, and trim the surplus.

Step 14: Bevel-Rip the Base

03 lampposts Photograph by Kolin Smith

Clamp a 2×10 cedar board to a sturdy floor with its lengthy edge overhanging. Use a round noticed to tear a 45-degree bevel alongside that overhanging edge.

If mandatory, clamp a protracted straightedge to the board to information you to a superbly straight reduce.

Step 15: Miter-Lower the Base

03 lampposts Photograph by Kolin Smith

Tilt the miter-saw blade to a 45-degee bevel and modify the miter angle to zero. Bevel-cut the two×10 into 4 lengths to wrap across the base of the lamppost.

Step 16: Connect the Base to the Publish

03 lampposts Photograph by Kolin Smith

Apply development adhesive to the again of the primary piece of base trim and press it to the lamppost, sq. finish flush with the tip of the cladding.

Use a pneumatic ending nailer and 2½-inch-long nails to connect it, then connect the remaining three base items similarly.

Use development adhesive towards the publish, however apply waterproof carpenter’s glue or polyurethane glue to every of the 4 mitered nook joints. And you’ll want to nail by way of the corners, as proven.

Sand all surfaces clean with a random-orbit sander fitted with a 100-grit disk.

Step 17: Sink the Publish

04 lamppost Photograph by Kolin Smith

Maintain a 2×4 block on high of the middle publish and faucet it with a 3-pound sledgehammer to drive the pointed finish into the bottom.

If mandatory, loosen the soil first with a shovel. Not less than one-third of the publish ought to prolong belowground.

Use a 2-foot degree to plumb the publish. Deal with it with teak oil if you wish to protect the colour.

Step 18: Cling the Lantern

04 lamppost Photograph by Kolin Smith

Twist a 1-inch screw hook into the underside of the 2×4 arm, and hold the candle lantern from it.

In case you wired the lamppost for low-voltage lighting, hold the fixture from the hook, then full {the electrical} connection.

Learn extra: The right way to unlock lg k40 with out password

Related Posts

Leave a Reply

Your email address will not be published.